FMEA (Failure Modes and Effects Analysis)#

Launch Manager FMEA
status: draft
security: NO
safety: ASIL_B
version: 0
realizes: wp__sw_component_fmea
doc__launch_manager_fmea
Generic Document

Note

Use the content of the document to describe e.g. why a fault model is not applicable for the diagram.

Failure Mode List#

Table 24 Fault Models for sequence diagrams#

ID

Failure Mode

Applicability

Rationale

MF_01_01

message is not received (is a subset/more precise description of MF_01_05)

<yes | no>

<Rationale if not applicable, otherwise link to filled out FMEA>

MF_01_02

message received too late (only relevant if delay is a realistic fault)

<yes | no>

<Rationale if not applicable, otherwise link to filled out FMEA>

MF_01_03

message received too early (usually not a problem)

<yes | no>

<Rationale if not applicable, otherwise link to filled out FMEA>

MF_01_04

message not received correctly by all recipients (different messages or messages partly lost). Only relevant if the same message goes to multiple recipients.

<yes | no>

<Rationale if not applicable, otherwise link to filled out FMEA>

MF_01_05

message is corrupted

<yes | no>

<Rationale if not applicable, otherwise link to filled out FMEA>

MF_01_06

message is not sent

<yes | no>

<Rationale if not applicable, otherwise link to filled out FMEA>

MF_01_07

message is unintended sent

<yes | no>

<Rationale if not applicable, otherwise link to filled out FMEA>

CO_01_01

minimum constraint boundary is violated

<yes | no>

<Rationale if not applicable, otherwise link to filled out FMEA>

CO_01_02

maximum constraint boundary is violated

<yes | no>

<Rationale if not applicable, otherwise link to filled out FMEA>

EX_01_01

Process calculates wrong result(s) (is a subset/more precise description of MF_01_05 or MF_01_04). This failure mode is related to the analysis if e.g. internal safety mechanisms are required (level 2 function, plausibility check of the output, …) because of the size / complexity of the feature.

<yes | no>

<Rationale if not applicable, otherwise link to filled out FMEA>

EX_01_02

processing too slow (only relevant if timing is considered)

<yes | no>

<Rationale if not applicable, otherwise link to filled out FMEA>

EX_01_03

processing too fast (only relevant if timing is considered)

<yes | no>

<Rationale if not applicable, otherwise link to filled out FMEA>

EX_01_04

loss of execution

<yes | no>

<Rationale if not applicable, otherwise link to filled out FMEA>

EX_01_05

processing changes to arbitrary process

<yes | no>

<Rationale if not applicable, otherwise link to filled out FMEA>

EX_01_06

processing is not complete (infinite loop)

<yes | no>

<Rationale if not applicable, otherwise link to filled out FMEA>

FMEA#

For all identified applicable failure initiators, the FMEA is performed in the following section.

.. comp_saf_fmea:: <Title>
   :violates: <Component architecture>
   :id: comp_saf_fmea__<Component>__<Element descriptor>
   :fault_id: <ID from fault model :need:`gd_guidl__fault_models`>
   :failure_effect: "description of failure effect of the fault model on the element"
   :mitigated_by: <ID from Component Requirement | ID from AoU Component Requirement>
   :mitigation_issue: <ID from Issue Tracker>
   :sufficient: <yes|no>
   :status: <valid|invalid>

  .. note::   argument is inside the 'content'. Therefore content is mandatory

Attention

The above directive must be updated according to your component FMEA.

  • The above “code-block” directive must be updated

  • Fill in all the needed information in the <brackets>